Install /e/OS on a Google - Pixel Tablet tangorpro

This guide installs /e/OS on your tangorpro. Read it through once before you start, so you don’t hit surprises partway in. Downgrading from a newer OS version than the /e/OS build you’re about to install can cause instability or brick some devices — check your current OS version first. Flashing is done at your own risk: /e/OS builds are provided as best effort, without any guarantee, and the /e/OS project takes no responsibility for the consequences.

Requirements

  • Back up your important data to an external storage device — some of the steps below format the phone, wiping any backup left on it.
  • Charge your phone above 50%.
  • Enable adb and fastboot on your PC — setup instructions.
  • Download every file listed in the Downloads section below before you start.
  • Use a real data cable — some cables only charge and can’t transfer data.
  • Enable USB debugging on your device — instructions.
  • Confirm your exact model in the Device Selector: where shown, hover the device name for the supported model number, and check it matches yours exactly.
  • Boot the stock OS at least once and check everything works — SMS, calls, and both over WiFi and LTE if available (some devices need VoLTE/VoWiFi used once on stock to provision IMS). Whatever’s broken on stock stays broken on /e/OS.
Warning: Log out of any accounts (Google, Samsung, Mi Account, etc.) set on the stock ROM before proceeding. Most vendors enable Factory Reset Protection (FRP): after a factory reset, a device that's still signed in will ask for the credentials of that account before it can be used again. Also remove any screen locks.

Downloads for tangorpro

Tip: Before installing /e/OS on the Google Pixel Tablet tangorpro for the first time, install the latest stock OS version 13 build on the device
official /e/OS A14

Each build includes /e/OS Recovery — no separate download needed.

Not sure which one to pick? See official vs. community builds.

  • Before following these instructions please ensure that the device is on the latest Android 13 firmware.

  • If your device is currently using a newer or older version than the required version, please upgrade or downgrade to the required version before proceeding with your /e/OS installation.

  • The required version is Android 13 , which may be lower than the /e/OS version you are about to install - this is not an error! If there are multiple updates of that version (e.g. security updates), make sure to use the latest!

  • If you need to upgrade or downgrade your device, please search online for guides. We are unable to provide specific instructions here and on our support platforms.

Unlocking the bootloader

These steps only need to be run once per device. Unlocking the bootloader will erase all data on your device — make sure anything you want to keep is backed up (see Requirements above). Not sure what unlocking changes on your device? See Bootloader relocking.

Tip: If you see no permissions fastboot while on Linux or macOS, try running fastboot as root.

  1. Enable OEM unlock in the Developer options under device Settings, if present.

  2. Connect your device to your PC via USB.

  3. On the computer, open a command prompt (on Windows) or terminal (on Linux or macOS) window, and type:

    adb reboot bootloader

    You can also boot into fastboot mode via a key combination:

    • With the device powered off
    • hold Volume Down + Power

  4. Once the device is in fastboot mode, verify your PC finds it by typing:

    fastboot devices

  5. Now type the following command to unlock the bootloader:

    fastboot flashing unlock

  6. If the device doesn’t automatically reboot, reboot it. It should now be unlocked.

  7. Since the device resets completely, you will need to re-enable USB debugging to continue.

Flashing additional partitions

This platform requires additional partitions to be flashed for recovery to work properly. The steps to flash the partitions are given below.

The partition files will be available in the /e/OS build or /e/OS recovery zip folders. Look for the file name starting with the partition name. For example, the vbmeta.img file may be named vbmeta-e-x.y-aX-YYYYMMDD123456-channel-codename.img. You can rename it to vbmeta.img if you want to — the part after vbmeta is just an indicator of the build date when it was compiled. If the files are not found in these zip folders, users can download them from the LineageOS wiki install page specific to this device and OS build.

Tip: If you encounter an error such as "No such file or directory" when executing a fastboot flash command, it is because fastboot cannot locate the image file. You can resolve this by either specifying the full path to the file (e.g., C:\Users\YourName\Downloads\boot.img) or by typing the first part of the command followed by a space (fastboot flash boot ) and then dragging and dropping the file directly into the terminal/console window.

  1. First unzip the /e/OS Recovery file linked in the section marked Downloads for tangorpro . The following files would show up in the location where you unzipped the contents of the eRecovery zip file

    • boot.img
    • dtbo.img
    • vendor_kernel_boot.img

  2. Next we manually reboot into bootloader or download mode

    • With the device powered off
    • hold Volume Down + Power

  3. Flash the downloaded image files to your device by typing (replace <...> with the actual filenames):

    fastboot flash boot <boot>.img
fastboot flash dtbo <dtbo>.img
fastboot flash vendor_kernel_boot <vendor_kernel_boot>.img

  4. Reboot to bootloader mode

    fastboot reboot bootloader

Installing /e/OS

Windows users: run these commands in Git Bash, not in the default command prompt.

Let’s proceed with the installation:

  1. Unzip the file you downloaded from the link in the Downloads for tangorpro section above.

    unzip <fileyoudownloaded>

    Replace <fileyoudownloaded> with the name of the file you downloaded. You can also unzip it using a File Manager/File Explorer.

  2. Confirm that the folder where you unzipped the files contains the following:

    • bin-linux-x86 directory - which contains linux tools including fastboot and adb
    • bin-msys directory - which contains Windows tools including fastboot and adb
    • bin-darwin directory - which contains MacOS tools including fastboot and adb
    • .img files - The .img files that are to be flashed onto the device.
    • flash_tangorpro_factory.sh - The installer script.

  3. Boot your tangorpro into bootloader/fastboot mode:

    • With the device powered off
    • hold Volume Down + Power

  4. Open a terminal (Linux) or Git Bash (Windows) in the folder that contains flash_tangorpro_factory.sh — right-click inside the folder and choose “Open terminal here” / “Open Git Bash here”. Then make the script executable and run it:

    chmod +x flash_tangorpro_factory.sh && ./flash_tangorpro_factory.sh

    The chmod step may require root/sudo privileges.

  5. The script flashes all required files and waits for input at the last step — proceed to locking the bootloader below.

Locking the bootloader

Warning: The bootloader is lockable in official builds only. The procedure to lock the bootloader will not work on community builds.
Tip: What locking the bootloader protects, and what it does not: see Bootloader relocking.

  1. Boot into bootloader/fastboot mode if not already there by

    • hold Volume Down + Power

  2. Once the device is in bootloader/fastboot mode, verify your PC finds it by typing:

    fastboot devices
    Tip: If you see no permissions fastboot while on Linux or macOS, try running fastboot as root.

  3. Download the avb custom key

  4. Erase the previous key fastboot erase avb_custom_key

  5. Flash the new key previously downloaded fastboot flash avb_custom_key pkmd_pixel.bin

  6. Lock the device fastboot flashing lock

  7. Use the volume key to select Lock the bootloader

Reboot the device

  1. Use power button to Start the device

    The reboot process may take 5 - 10 minutes

Disabling OEM Unlocking.

Once you boot your device after locking bootloader:

  1. Finish SetupWizard
  2. Go to Settings > About phone > Build number.
  3. Tap the Build Number option seven times until you see the message You are now a developer! This enables developer options on your device.
  4. Return to the previous screen and go to System to find Developer options at the bottom.
  5. In Developer Options, turn OEM Unlocking off.
Success: Congratulations! Your phone should now be booting into /e/OS.
To find some troubleshooting tips… click here

adb

  • Getting a Total xFer ':' 0.01x message - Try to upload the /e/OS to internal storage and retry to install
  • adb ':' sideload connection failed ':' insufficient permissions for device error - Try to execute the commands adb kill-server and adb start-server and retry
  • Getting an insufficient permissions error - Try the solution given here
  • When running "adb devices" in bash a device is shown as "unauthorized" - Try the solution given here

Connectivity

  • Trying to troubleshoot mobile connectivity issues - Read this guide


Please share your experience , suggest tips or changes to this install guide documentation by visiting the Pixel Tablet specific topic on our community forum. To report issues in /e/OS please refer this guide

This documentation “Install /e/OS on a Google - Pixel Tablet - “tangorpro”” is a derivative of “install LineageOS on tangorpro” by The LineageOS Project, used under CC BY.