Install /e/OS minimal on a Wingtech Redmi 2 - “wt88047” beta

The instructions in this guide will assist you to install /e/OS on your wt88047. Please read through the instructions at least once before actually following them, so as to avoid any problems later.

It is important that you know that downgrading Smartphones on OS versions greater than the /e/OS OS version you plan to install, can cause instability or at worst brick some devices. We recommend that you check your current OS version, before attempting the installation.

It is advisable to flash your device only if you know what you are doing and are ok taking the associated risk. All /e/OS builds are provided as best effort, without any guarantee. The /e/OS project and its project members deny any and all responsibility about the consequences of using /e/OS software and or /e/OS services.

Requirements

• If required take a backup of all important data from your phone on an external storage device before proceeding.
• Do not take a backup on the same device as some of these actions will format the device and delete the backup.
• A guide on backing up with TWRP is available here
• Ensure your phone is charged more than 50%
• Check that adb and fastboot are enabled on your PC. If not you can find the setup instructions here
• Download all the files and images mentioned in the download section below before starting the installation

• Make sure you have a working data cable to connect your device to the PC. There are cables which are only for charging and do not transfer data.

• Enable USB debugging on your device. You can find the instructions here
• Make sure that your model is listed in the Smartphone Selector. Check the model supported. Where available, information on the model supported should show as a pop-up when you hover the cursor on the Device name. The model number supported should be the exact same.
• Boot your device with the stock OS at least once and check every functionality.

Please share your experience , suggest tips or changes to this install guide documentation by visiting the Redmi 2 specific topic on our community forum.

To report issues in /e/OS please refer this guide

Downloads for wt88047

• Custom recovery (not required if you already have it running on your phone)

• /e/OS build : Nougat community

To understand the difference between /e/OS builds check this guide

• Check the Pre-Install Instructions section below for some additional downloads for your device.

• Download the relevant firmware zip file from here.

  To get the details of the relevant firmware read the next section Updating firmware

Updating firmware

• If you are installing from LP (5.x) stock MIUI, nothing needs to be done.
• If you are installing from KK (4.4) stock MIUI, you will have to update the device’s firmware.

1. To find your model number, “Open “Settings”, navigate to “Phone Info”, and take note of the model number below the “model” header:
   • Devices with model numbers 2014811, 2014812, 2014817 2014818, 2014819, and 2014821 should download the firmware labeled wt88047.
   • Devices with model numbers 2014813, and 2014112 should download the firmware labeled wt86047.

2. Sideload the firmware file downloaded from the link in the Downloads section

   Tip: Sideload requires actions in two places to be done. One on your phone in the TWRP UI and secondly on the connected PC which should have adb enabled. Also note the sideload process while running may stop abruptly around 50%. The console would show a message Total xfer: 1.00x. This would mean that the transfer has successfully completed.
   • On the device in TWRP,

     select Advanced, ADB Sideload, then swipe to begin sideload.

   • On the host machine, in the console , start the sideload of the package by typing

    adb sideload filename.zip
   

   Tip: Change the filename to the name of the file you downloaded

Installing a custom recovery

1. Connect your device to your PC via USB.

2. On the computer, open a command prompt (on Windows) or terminal (on Linux or macOS) window, and type

    adb reboot bootloader
   

3. Once the device is in fastboot mode, verify your PC finds it by typing

    fastboot devices
   

4. Flash recovery onto your device

    fastboot flash recovery recoveryfilename.img
   

   Replace the recoveryfilename with the name of the recovery image you downloaded in the previous section

5. Now reboot into recovery to verify the installation
   • Lorsque l’appareil est hors tension
   • hold Volume Up + Volume Down + Power.

Installing /e/OS from recovery

1. Before proceeding ensure you have downloaded the /e/OS for your device, from the link given in the Downloads section above

2. If you aren’t already in recovery mode, reboot into recovery mode

   • by typing the below command in the console of an adb enabled PC

    adb reboot recovery
   

3. In TWRP return to main menu, then tap Wipe

4. Now tap Format Data and continue with the formatting process.

   Here a new screen may show where you will have to type Yes and confirm the action by clicking a button.

   Caution: Format Data will remove encryption as well as delete all files stored on the internal storage. Remember to take a backup first. Check Requirements section above.

5. Return to the previous menu and tap Advanced Wipe.

6. Select the Cache and System partitions to be wiped and then Swipe to Wipe

7. Sideload the /e/OS .zip package.

   Tip: Sideload requires actions in two places to be done. One on your phone in the TWRP UI and secondly on the connected PC which should have adb enabled. Also note the sideload process while running may stop abruptly around 50%. The console would show a message Total xfer: 1.00x. This would mean that the transfer has successfully completed.
   • On the device in TWRP,

     select Advanced, ADB Sideload, then swipe to begin sideload.

   • On the host machine, in the console , start the sideload of the package by typing

    adb sideload filename.zip
   

   Tip: Change the filename to the name of the file you downloaded

8. Once installation has finished, return to the main menu, tap Reboot, and then System

Please share your experience , suggest tips or changes to this install guide documentation by visiting the Redmi 2 specific topic on our community forum.

To report issues in /e/OS please refer this guide

Cette documentation est dérivée de “install LineageOS on wt88047” du Projet LineageOS, grâce à la license CC BY.